LEGENDS(tm) 7.0 to 7.1 Upgrade Guide
Authored by Jeffrey D. Hoffman.  Copyright(c) 1996.  All rights reserved.

Upgrading 7.0 software to 7.1
Addendum to Sysop Handbook, Chapter II

Upgrading your LEGENDS or LEGENDSlite 7.0 software to the equivalent 7.1
software is very simple. The following steps will guide you through this
automated upgrade sequence which is handled, for the most part, by the new
version of the installation software included in this archive.  For the
remainder of this documentation LEGENDS and LEGENDSlite will be universally
referred to as LEGENDS unless directly specified.

1.  Make a back-up of your existing LEGENDS 7.0 software.  In the event that
    anything goes wrong, you always want to ability to backstep a version and
    start over.

2.  Copy and extract the LEGEND71.ZIP file into the directory containing your
    existing LEGENDS 7.1 software.  Be sure to use the overwrite flag (-o) when
    you extract. This flag will insure that any existing documentation and
    data-files for the installation will be overwritten with the latest
    release. Within this section, it is assumed that the software was placed in
    a directory called LEGENDS7 as specified by the Sysop Handbook.

C:\> cd \tbbs\legends7
C:\TBBS\LEGENDS7> pkunzip -o legend71.zip

3.  Type INSTALL7.EXE -U to initiate the installation program.  The appended
    flag -u forces the installation program to upgrade existing software in the
    directory without interfering with the existing game-in-progress.

C:\TBBS\LEGENDS7> install7 -u
 
4.  The installation software will determine whether or not there is existing
    software in the directory.  If so, it will begin processing and upgrading
    the software and databases to function under 7.1.  When the upgrade is done
    you will be returned to the DOS prompt.

5.  The installation program creates new configuration files but saves your
    original settings as .ORG files.  Within the LEGENDS SYSTEMS\ directory you
    will find LEGENDS7.ORG.  Use this file to assist you (as reference) to
    configure LEGENDS 7.1 to your needs.  Notice that several new flags are
    available to customize LEGENDS.  Refer to the Sysop Handbook for more
    information.

6.  You need to modify the existing LegendTASK ghost event in your TBBS
    configuration.  Using CEDIT, modify your specified ghost task(s) for the
    new information required by the ghost event.  The SYSTEMS\LGNDTASK.CFG file
    contains all of the settings for each ghost event you define.  Consult
    chapter III in the Sysop Handbook for further details.

Entry  #, Occurs on Line   16 at 07:00 on Sun,Mon,Tue,Wed,Thu,Fri,Sat
Type = 200 OptData = c:\tbbs\legends7\lgndtask.tpg /Q && /E=1

    This setting would instruct the LegendTASK event to use the flags specified
    under #DEFINE EVENT1= in the configuration file.

7.  Your AUTOEXEC.BAT file needs to be updated with a single line.  This line
    is required to make the executable LegendTASK maintenance software work
    properly.

set clipper=f99

    Be sure to either run your AUTOEXEC.BAT file or reset your system prior to
    running the LegendTASK software.

8.  The final step to getting LEGENDS up and running is to add the external
    maintenance executable to your daily TBBS maintenance routine.  Somewhere
    within your maintenance file, you need to add the following lines of code.
    Again, these settings are covered in detail in the Sysop Handbook, Chapter
    III, but for this example each daily the maintenance software will purge
    inactive players after twenty- five days.

rem Perform the daily LEGENDS maintenance by running the executable version of
rem LegendTASK.
cd \tbbs\legends7
lgndtask.exe -a:25

9.  Run your BBS.

Further information for customizing your LEGENDS 7.1 software is available by
reading chapter III in the Sysop Handbook.  If you haven't already, please
refer to the WHATSNEW.TXT file for a listing of new features and bugfixes in
this, the latest version of the software.
